IPD DT

DT_ALSZ

Deutsch DT Series of environmentally-sealed connectors are designed specifically for cable to cable applications on the engine or transmission, under the hood, on the chassis or in the cab. Where signal level circuits in harsh environmental conditions, where even a small degradation in connection may be critical, the Deutsch DT Series general purpose connectors will provide the reliability and performance at the lowest cost.

Thermoplastic ( -55 C to + 125C rated) housings and silicone seals are used to allow the connector to withstand conditions of extreme temperature and moisture. The connector may be employed with either solid-copper crimp type contacts for critical circuits or budged-minded stamped and formed contacts. In either selection, the spring action is designed in the socket and shrouded by by a stainless steel hood that provides closed entry for positive axial alignment during mating, and eliminates probe damage from occurring. Contact insertion and withdrawal require no special tools and are retained in locket position by dielectric fingers, molded as an integral part of the housing. Contrasting colored secondary locks are assembled at the mating interfaces. If by chance the secondary locks are not properly seatled during assembly, they will be pressed into locket position during the mating of the connector.

If you want your electrical system to be trouble free, providing years of service at the lowest cost specify the Deutsch IPD DT Series connector.

Technical characteristics:

Operating temperature: -55 0C ÷ +125 0C
Current rating: Max 13 amps all contacts
Sealing: To IP67.
No. of contacts: 2, 3, 4, 6, 8, 12.
Shell material: Rugged thermoplastic.
Seals Material: Silicone Elastomer.
Contact: Crimp, copper alloy, nickel or gold plating.
Physical Shock: No locking, unmating or other unsatisfactory result after 50g's in each of tree mutually perpendicular planes.
Dielectric Strength: 1500 volts minimum.
Insulation Resistance: 1000 megohms minimum at 25 0C.
Durability: No electrical or mechanical defects after 100 cycles of engagement and disengagement.
Contact Millivolt Drop: No. 16 contacts - 60 millivolt drop using 16 AWG wire (less drop through wire). Test current 13 amps.

Connector Part Numbering System

DT

06

-

3

S

*

-

****


=>






Series Prefix

=>





04 - Receptacle
06 - Plug



=>



Number of Contacts




=>


Contact type:
P - Pins
S - Sockets





=>

Polarizing Position (If Applicable)







=> Special Modifications

Secondary Lock Part Numbering System

W

3

S


=>

Secondary Locking Wedge

=>
Number of Contacts


=> Contact type:
P - Pins
S - Sockets

Contact Arrangements

Benefits:

  • Tactile and audible coupling feedback.
  • Long service life.
  • Engine compartment rated.
  • Meets most harness design requirements.
  • Superior environmental seal.
  • Seals .008 to .145 dia. Insulation.
  • Data transmission or power distribution terminals.
  • Meets most power requirements.
  • reliable contacts retention system.
  • No special tools required.
  • Low installation costs.

Tooling


Contacts:

Solid - Crimp type

Qpin1

contact part
number
size & type A max B min C min D min wire gage
range
recommended
strip length
hand
crimp tool
0460-202-16141 16 pin .821 .066 .103 .250 16 and 18 .250 ÷ .312 HDT-48-00
0462-201-16141 16 soc .759 .066 .103 .250 16 and 18 .250 ¸ .312 HDT-48-00
0460-215-16141 16 pin .821 .076 .103 .250 14 and 16 .250 ¸ . 312 HDT-48-00
0462-209-16141 16 soc .757 .076 .103 .250 14 and 16 .250 ¸ .312 HDT-48-00

Stamped and Formed - Crimp Type


contact part number size & type wire gage range recommended strip length hand crimp tool
1060-16-0122 pin 16 and 18 .125-.175 DTT- 16-00
1062-16-0122 socket 16 and 18 .125-.175 DTT-16-00
1060-14-0122 pin 14 and 16 .125-.175 DTT-16-00
1062-14-0122 socket 14 and 16 .125-.175 DTT-16-00

Assembly

Contact Insertion

  1. Grasp crimped contact approximately (25.4mm) one inch behind the contact barrel.
  2. Hold connector with rear grommet facing you.
  3. Push contact into connector grommet until a click is felt. A slight tug will confirm that it is properly locked in place.
  4. Once all contacts are in place, insert orange wedge with arrow pointing toward exterior locking mechanism. The orange wedge will snap into place. Rectangular wedges are not oriented. They may go in either way.

Contact Removal

  1. Remove orange wedge using needlenose pliers or a hook shaped wire to pull wedge straight out.
  2. To remove the contacts gently pull wire backwards, while at the same time releasing the locking finger by moving it away from the contact with a screwdriver.
  3. Hold the rear seal in place, as removing the contact will displace the seal.

Related Topics


PDF Catalog IPD DT



© 2012 Imcon Electronics, s. r. o. Representative of compagnie DEUTSCH GmbH. Bož.Němcové 1, 66451 Brno-Šlapanice; Czech Republic
tel. +420 545 234 440; fax. +420 545 233 169; e-mail: